Hydrogen

hydrogen is a very combustible fuel all we need to do is great ways to use it just like We do with other fuels. There is not going to be change unless We start to make use of hydrogen as fuel.

 

There are people out there that will fight you over the change from fossil fuels.These people you know them by the name of Shell Oil CO,Standard Oil,Chevron Oil there are hundreds of these people.

 

Making Hydrogen fuel is the key to all the country's problem.Fossil fuel is our  problem across the globe. There is other country's that use oil to generate money to finance  War agents other country’s.

 

I know of about three ways to use Hydrogen as a fuel source.  We if we as people start demanding Appliances that use Hydrogen and start repairing the old one and refuse to by new appliances that use fossil fuel there will be a change.

 

I have a year Mitsubishi that is in perfect condition and I  have a picture of it to show You. I am doing this to let Every one know that all You have to do is to refuse to buy another vehicle That operates on Oil.

Pollution

Where are we today

we are still driving dinosaurs

what that is, we are still driving dinosaurs what we do is we are still building vehicles that burn fossil fuel. We change the appearance of the car but a computer in them. We change the outside of the vehicle but they are the same vehicle that are great grand parents were driving more than 100 years. Then we drive these vehicles that burn fossil fuel and we think that we are advancing our technology. That's not the case. What we are doing is we're polluting on a grand scale.Some think that were ruining the ozone . The ozone is changing all the time. Not much we can do about that, but that's not of course what we are doing we are polluting the earth . Here's what I believe we're doing. We pump oil from deep below the ocean floor.

We spill oil in our ocean and create toxic waste. We pollute the air our children breathe.

So what will it take to get people from driving dinosaurs is it going to take a catastrophic meltdown. People out there want to control you. . These people feel if they control energy they control you. So you think what can I do about that. You can do a lot of things you can read you can think you can experiment you can build things you can write things. These are the things you can do to stop polluting. Teach your children that there are alternative fuels .

Humans

What are You going to do?
Gas is going through the roof and no one thinks that there is nothing they can do.
What about a World wide Embargo Do You think that that might get some attention?
Sure That is something to think about .

How would We go a bought doing that? Maybe we should not even think a bought that. Here we go again, but what if we could as humans and not subjects for the energy companies make things happen.


Or make things happen when it was time to do so. We could stop all kinds of things we would have more control over our lives . There are lots of good things out there that our government put together for our Country and I like them a lot.


But energy companies are the controllers of our lives. I don't have to be real About this estimate what we spend on energy it is a lot of money is that not true? So back to the Embargo what if that was possible?

I believe A long time ago People had a lot of things going on, one was they had imagination and drive to do things! Lets talk about these things on this blog see what minds we can bring together.


Love to here from You

Eugene Island Pipeline Spill

GOM, LA 2009-Jul-26

On Sunday afternoon, 26 July 2009, NOAA was notified of an oil spill 33 miles offshore and 60 miles southwest of Houma, LA that occurred on Saturday afternoon. The leak was from the Eugene Island Pipeline System and approximately 63,000 gallons of oil was released. Pre-approved dispersant was applied to the heaviest concentrations of the spill. On water recovery was also initiated. NOAA is providing on-going trajectory and weather support.

There’s danger out there

There’s danger out there, all kinds of fuel being spilt everywhere
You can look around and you watch the news put people don’t seem to mind all the chemicals being spilt.

Chemicals on the spillways, oil in our oceans, smog in our cities, so many people developing lung cancer. Lots of our Children developing lung conditions so many of our mothers and fathers dead or dying from some illnesses we cant even diagnose because to many people to tell you that You are allowed so many parts per million.

 

Look why is it we refuse to make a change every one is doing it when it comes to what You eat where You sleep what You watch on Television. Well make some more changes don’t buy any vehicles that run on oil.

 

So many city’s have buses that run on hydrogen and they tell you right on the side of  them . Well where are our cars that run on Hydrogen. There not here because We keep buying cars that run on gas and diesel.

How to Build a # 1 Hydroliser

Hydrogen Build a # 1 Hydrolyser
I have built lots of hydrolysers in the past and I have the best hydrolyser ever built and I am going to share it with You.
You will use these 5 items to build Your hydrolyser.

1. I take an inch and a quarter diameter piece of stainless tube 5 inches long, and wind stainless wielding wire around the tube.

2. I take 2 pieces of plexiglass one piece is 3/16 inch thick 6 inches long x 6 inches wide And another piece of plexiglass 1/8 inch thick 6 inches long x 6 inches wide. Then I cut all the plexiglass in 1/4 inch strips on a table saw. These parts will make up our insulators.

3. I buy stainless steel all thread usually comes in 3 Foot Lengths . I used the size 10.20 . The all thread will be cut to make two 6 inch ln lengths. These are called conductors.

4. I purchase a role of stainless steel wielding wire about .030 in diameter from the local wielding shop.

5. I bought from Homedepot a tube of clear Epoxy to assemble the hydrolyser.

In the next 6. steps We will build My HYDROLYSER HERE AT HOME.
We will be using epoxy to hold our parts together and if it is done right it will be magnificent to look at.
Before We get started look at #2 drawing for a moment and see how the insulators are placed. There will be three 3/16 inch insulators and one 1/8inch insulators on the first wind . You will do the same on the second wind .

1.Apply marks inside the tubes like if You where going cut the tube in quarters. Inside the tube so the marks are not visable from the outside.

2.Before you epoxy you must roughing Length-wise the tube where You are going to apply the epoxy to hold the insulators. In the drawing #1 below You see only one of the insulators applied to the tube the gray area is where it is roughed up for the epoxy.

tip.The insulators will not be placed center on the stainless tube. At one end will be a 1/4inch protruding over the end. Then there will be 3/4inch over the other end. Like in diagram #2

3.Now epoxy the insulators on in a cross pattern three 3/16x5inch and one 1/8 x5inch insulators
(there are now 4 insulatorss all together on the tube)

4.Now you will epoxy one stainless 10.20 6inch conductor on the 1/16inch insulators in this manner .The end of the conductor will began at the edge of the tube the rest of the conductor well protrude over the insulators at the 1/4inch end . look at drawing #3

5.Now put two 2inch hose clamps to hold everything together untill it is fully wound.
(Now You will wind Your first coil . And You must wind it tight )

6.You must start by wraping the steel wire around one end of the conductor then start winding the coil it must be wound tight.You must be about A 1/8inch apart on each wind and as you reach the hose clamps take them off. Only wind over the steanless steel tube not to each end of the insulators.

7.when You reatch the end You must wrap the end of the wire around the other end of the conductor and cut the remaining excess wire.
(You are now done with the first part of the coil.)

8.You must cut one inch off the insulators. You must now epoxy the other three 3/16x5 over the stainless steel wire not the conductor .
Now You will Epoxy the last insulators and that is the 1/8inch thick x5" long over The conductor sealing the conductor completely except the 3/4 inch that protrudes over the 1/4inch end like in diagram #4.

9. Put the hose clamps back on. And start the last wind. Like You wound the first coil. You now have built the best Hydrolyser element ever developed.

Solar Panel Regulator